Company News Industry News Maintenance Knowledge
Current position:HOME > News > Company News

China HECHA recommends our products

editor:admin │ Release time:2018-06-28 

China HECHA recommends our products:

The forklift is an industrial handling vehicle, which refers to various wheeled handling vehicles that carry out loading, unloading, stacking and short-distance transportation of the palletized goods.


Scope of application:

Industrial handling vehicles are widely used in ports, stations, airports, freight yards, factory workshops, warehouses, distribution centers and distribution centers. The loading, unloading and handling of pallet goods in cabins, compartments and containers is a must for pallet transportation and container transportation. Indispensable equipment.


Operating procedures:

(1)Check vehicle

1.Before the forklift is in operation, the appearance should be checked and fuel, lubricating oil and cooling water should be added.

2.Check start, run and brake performance.

3.Check that the lighting and audio signals are complete and effective.

4.Check whether the pressure and temperature are normal during the operation of the forklift.

5.After the forklift is running, the external leakage should be checked and the seals replaced in time.

6.In addition to checking the above contents, the battery forklift should also check the circuit of the battery forklift according to the relevant inspection contents of the battery car.

(2)Start

1.Before starting, observe the four sides and confirm that there are no obstacles to the safety of driving, first whistle, then start.

2.For vehicles with air brakes, the brake barometer reading must reach the specified value before starting.

3.When the forklift starts, the driver should first confirm that the cargo is stable and reliable.

4.Start slowly and smoothly at the start.

(3)Driving

1.When driving, the height of the bottom end of the fork should be 300-400mm from the ground, and the gantry must be tilted backward.

2.Do not raise the fork too high while driving. When entering or leaving the work site or on the road, pay attention to the obstacles in the sky. When the load is driving, if the fork rises too high, it will increase the overall center of gravity of the forklift and affect the stability of the forklift.

3.After unloading, the fork should be lowered to the normal driving position before driving.

4.When turning, if there are pedestrians or vehicles nearby, signal should be issued and high-speed sharp turns should be prohibited. High-speed sharp turns can cause the vehicle to lose lateral stability and tip over.

5.Internal combustion forklifts are strictly prohibited from stalling when going downhill.

6.In non-special circumstances, it is forbidden to brake the load while driving.

7.When the load travels more than 7 degrees and goes up and down with a speed higher than the first gear, the brake must not be used in non-special circumstances.

8.The forklift must comply with the in-plant traffic rules during operation and must maintain a certain safety distance from the preceding vehicle.

9.When the forklift is running, the load must be at the lowest position that does not hinder the driving. The gantry should be properly tilted backwards. When stacking or loading, the load should not be increased. When carrying a large object, the object blocks the driver's line of sight, and the forklift should be turned down at this time.

10.The forklift is controlled by the rear wheel, so you must always pay attention to the swing behind the car to avoid the sudden turn of the car that often occurs when the beginner drives.

11.Do not turn on the ramp,should also not travel across the ramp.

12.When the forklift truck is going downhill, it should be reversed to prevent the cargo from falling down.

(4)Loading and unloading

1.When loading the goods, adjust the distance between the two forks as needed to balance the load of the two forks. Do not skew. One side of the item should be placed against the shelf. The weight of the fork should meet the requirements of the load center curve sign.

2.The height of the load must not obscure the driver's line of sight.

3.The brake must be braked with the brakes during loading and unloading of the item.

4.When the forklift truck approaches or evacuates the item, the speed of the vehicle should be slow and steady. Pay attention to the wheels and do not crush the objects, wooden mats, etc., so as to prevent the crushed objects from flying and injuring people.

5.When picking up the goods with forks, the forks should be forked as far as possible into the load, and the fork tip should not touch other goods or objects. The minimum gantry back tilt should be used to stabilize the load so that the load does not slide backwards. When the load is lowered, the gantry can be tilted forward a small amount to facilitate loading and unloading the fork.

6.It is forbidden to fork the cargo at high speed and collide with hard objects with the fork.

7.When the forklift is working, it is forbidden to stand on the fork.

8.Forklift forklift operations, it is forbidden to stand around the forks to prevent the goods from collapsing and hurting people.

9.It is forbidden to use the forklift to lift personnel to work in high places, so as to avoid accidents in high places.

10.It is not allowed to use the brake inertia to slide the item.


点击这里给我发消息 点击这里给我发消息